easy wood projects
John Tetreault, Associate Art Director 4 users recommend
I added dovetailed rails to the case front. Glued and attached with copper nails. I left one rail below the center gallery un-glued and turned it into a secret drawer.John Tetreault
To seal any possible lead solder from contact i used a spray satin polyurethane. Four coats on each side left a nice sheen.
John Tetreault
An 1/8th inch kerf from the tablesaw blade held the panels firmly in place. I used through tenons for the frame construction.
John Tetreault
Heres the door glue-up with the panels locked in.
John Tetreault
I had to rip straight edges on all the door parts to get nice square mortise and tenon joints. I wanted to get back the natural patina edge on the center gallery section of the door, so I carefully chose a close grain (and texture) match from scrap pieces and glued on 1/4 thick edging.
John Tetreault
Attaching the door was a bit tricky because of the natural edge of the case front. I first attached the hinges to the straight edge of the door. Then I fine tuned the depth of each hinges mortise in the case side to get the door to swing smoothly.
John Tetreault
I added a 12 light LED light strip in the gallery and a single blinking red light to each of the circuit panels just for fun. I first drilled a hole in the panel and attached the single light. Then ran the wires across the panel, securing them with tiny copper wires looped through tiny holes in the panel. To pass by where the door swings, I used the black casing from standard house wiring and fed it through the edge of the stile. I left a little slack and then attached it to the underside of the shelf.
John Tetreault
Heres the switch set into the top.
John Tetreault
I drilled holes into the back to recess the wire nuts for the light connections but left the rest of the wires exposed.
John Tetreault
Finished photos! Heres the cabinet from the front. With a slow shutter speed on the camera, you can see both red blinking LED lights in the panels. The center gallery fits a Bose sound dock perfectly and surrounded by all the antique wood, it sounds great!
John Tetreault
Heres the front view with the door open showing the hidden drawer. The drawer is shallow but great for a small laptop or ipad.
John Tetreault
Detail showing the contrast between the weathered wood and satin finished circuit panel.
John Tetreault
I added dovetailed rails to the case front. Glued and attached with copper nails. I left one rail below the center gallery un-glued and turned it into a secret drawer.
Its always interesting to try and combine the old and rough, with the new and smooth. Such was the case with my first Furniture Lab project. Dubbed the "Tech Cabinet," this pseudo-chimney cupboard incroporated hi-tech-looking printed circuit boards and LED lighting, with weathered old barn boards that have been aging in the great outdoors for the better part of 100 years (or maybe even more!).
Learn About the Entire Tech Cabinet Build
What is Furniture Lab?Recycling Found Objects into Fine FurnitureTech Cabinet: Part 1Tech Cabinet: Part 2
This project didnt come to be without its fair share of problem situations that required smart solutions. Trying to cut precise joinery with wood that has largely been left untouched (ie: un-milled) can be quite difficult, to say the least, but all the trial-and-error, finagling, and head-scratching were worth it. The contrasts that abound on this piece make it what it is, and I think its fair to say that there arent too many cabinets quite like it.
See my gallery of photos for a detailed description on the construction process. And dont forget to check back for more Furniture Lab projects from other Fine Woodworking staffers. Who knows, I might throw myself back in the mix too--sooner than you think!
Watch the Furniture Lab Junkyard Visit
Be sure to read Asa Christianas story outlining the original idea and intent of Furniture Lab, plus, watch our original Furniture Lab junkyard visit. John Tetreault, Tom McKenna, and Anatole Burkin visited an old salvage yard for some quirky design inspiration.
Inspired by the steampunk and recylced furniture movements, Furniture Lab allows the editors of Fine Woodworking magazine and FineWoodworking.com to really let their hair down.
Here, youll find us cooking up all manner of design experiments. We aim to incorporate salvaged and recylced items into our furniture and will be veering way off the traditional path of Fine Woodworking.
Click Here and Start WoodWorking
Do you find information about easy wood projects are you looking for? If not, below may help you find more information about the easy wood projects. Thank you for visiting, have a nice day.
0 komentar:
Posting Komentar